Ampps Portable How To Properly Size

You may also want to see our article on what kind of extension cord do I need for even more info.

This chart breaks down how both the wire gauge and length of the extension cord affects its ability to convey power to a corded tool.

Running a 15-amp tool How about a full 20-amp tool We can help you understand what length and gauge extension cord gets you and keeps you up and running.

If you want to know more, like what is AWG or American Wire Gauge, see below.

However, if you simply want to know what gauge extension cord you need to support a particular amount of amps, or how long an extension cord you can run without losing power, here you go.

Getting a firm grasp on understanding wire gauge and amps and how they interrelate can protect your tools and keep you safe.

We broke our charts down by extension cord length since thats where most people start when looking for the right gauge cord: 100-foot Extension Cords If you want to run a 100-foot long extension cord, you have to take into account the fact that youre essentially creating a huge resistor.

With that in mind, you typically dont see 100-foot cords exceeding 15-amp (15A) capacity.

Current Draw Minimum Wire Gauge Voltage Drop 20A 10-gauge 4.00 15A 12-gauge 5.00 12A 12-gauge 4.00 10A 12-gauge 3.33 Yields a 5 voltage dropthe maximum allowed in our calculations.

Consider using the next size up for anything that is at or near 5 oreven betteropting for a shorter cord whenever possible.

Extension Cords Current Draw Minimum Wire Gauge Voltage Drop 20A 12-gauge 3.33 15A 14-gauge 3.88 12A 14-gauge 3.10 10A 14-gauge 2.58 25-foot Extension Cords Current Draw Minimum Wire Gauge Voltage Drop 20A 14-gauge 2.58 15A 14-gauge 1.94 12A 14-gauge 1.55 10A 14-gauge 1.29 See below for some recommendations on extension cords which should match the above requirements.

Assumptions for Sizing Extension Cord Length For our extension cord size chart calculations, we assumed 120V single phase with a power factor of 1.

We also utilized the 2014 NEC Chapter 9, Table 9 numbers for impedance and voltage drop calculations.

With that being the case, only one of our recommendations hit that level, the 100-foot 12-gauge extension cord with a full 15A draw.

This might be an unusual application for some, but we felt it represented a great scenario.

It helps you understand what happens when using a 100-foot extension cord on a tool with a high current draw.

Why Understanding Wire Gauge and Amps Matters Everyone on a job site or remodel has some experience with running extension cords.

For larger tools that require them, its not enough to simply tap into the temp power pole or a nearby outlet.

You have to ensure that if your tool requires 15 amps, it gets 15 amps.

First, you can tax the tool motorcausing it to work harder to draw the energy it needs to run.

If that straw isnt large enough to deliver air, you struggle to breathe.

Use it in that state for too long, and the wire insulation could melt.

This particularly holds true if you keep the wire in a coil, which creates resistance and a magnetic field that heats up.

Some Helpful Dos and Donts DO: Understand how much current you need to draw for your tool or appliance Properly size the wire gauge to the length and current draw required Keep your cables as short as possible for higher current tools Unroll extension cords fully so they arent coiled during use DONT: Use cables not properly rated for your tool and the length of cord Keep your extension cords coiled during use Use a cord that lacks a ground plug (either missing or broken) Run multiple high-current tools off a single cord or circuit Use a long extension cable if you have a short one handy Hopefully, you found our extension cord size chart helpful and direct to the point.

Ampps Portable How To Properly Size

Understanding wire gauge and amps and how to properly size your cords for the tool and distance can make your tools last longer and run more optimally.